How To Replace Drywall

04/19/2020 Leave a comment Demo

Drywall has replaced the traditional cement plaster walls in the modern construction industry. Drywall is a product of gypsum plaster, which is usually hard-pressed between two paper sheets. Any water leakage on drywall can make it rot and look ugly. Now let us have a look at how to replace drywall with several working tools for the project required.some of these tools are; a joint tape, some drywall screws, drywall saw, utility knife, a prybar, screw gun, joint tape, approximately five-inch drywall knives, and a drywall compound. With the tools ready, the procedure is pretty straightforward.

Before starting your drywall replacement, select items and areas you do not want to get dusty and dirty and cover them. Such areas, like the floor, need to being covered with polythene or cloth. You need to cover air conditioners and vents using masking tape to protect them from the fine dust. Furniture will need to be either moved out or appropriately covered. Power connections also need to be cut off, and all electrical appliances removed as well. The reasons for drywall replacements vary from replacing a damaged one, upgrading the wall, or fixing a pipe. When you have done this, make sure the drywall you are repairing does not have crisscrossing pipes and wires, and with that, you are good to go.

Step One

Assess the drywall that needs to being replaced. The damaged part of the wall can be removed using a prybar or by the use of a utility knife. Use a screw gun to remove all the visible installation screws that were initially used to erect the drywall. Pull the drywall having nothing holding it in place.

Step Two

The second step is to make a replacement of the drywall and maintain the initial arrangement if a sheet was vertical replace with a vertical panel and if a panel was horizontal, replace it with a horizontal one. Use a screw gun to fasten screws on the drywall and drive the screws until they are slightly submerged on the drywall face, but remember the top part of the drywall is a paper, so do not break it.

For other drywall replacements like doors and windows, cut the same size of the drywall parts being removed; this can be achieved by using a drywall saw or a utility knife. Be accurate when measuring and cutting to avoid having a lot of drywall wastes.

Finally, you can now tape all seams of the replacement, now apply the joint compound over every seam. Allow the compound to dry and reapply two other coats allowing the coats to drying time before a consecutive coat is applied. The same compound is used to coat all the screws until they are no longer visible. When all this is done, you now get a pole-mounted sander for sanding the compound until the drywall surface becomes smooth. Some fine dust here may be harmful to your eyes. Therefore you need some goggles when sanding. Having done that you will have replaced your drywall

How To Paint An Ugly Wall

04/14/2020 Leave a comment Painting

Ugly walls can ruin the overall look of your home. No matter how hard you try to fix your furniture, it will still look bad. The best thing to do is to just paint it so that it will look better. However, there are some issues when painting uneven walls. You have to fix those issues first before doing any painting job.

1. Fix the Surface First

Before doing any painting, make sure to fix the surface of the ugly wall first. It can look chipped, damaged, or just uneven. You can still do something about it. No matter how ugly the wall is, all it takes is patience and hard work. Thorough surface preparation is a must if you want to have a beautiful wall after all your hard work. Skim coat is the best way to prepare your wall surface. Depending on how bad it is, you may need to do the skim coat entirely.

If you have the skills needed to do this by yourself, then go ahead and start doing it. However, it can be tedious and you may want to consider a professional to do this for you. But if you’re not aiming to have a super smooth wall surface, you can just go ahead and do it on your own. Just make sure that you have all the tools and materials that you need to make that surface smooth.

2. Just Cover It Up

If you’re not into making your walls smooth, why not do a textured painting instead? It can be a good idea instead of skim coating everything first. The textured wall painting technique can give your wall a different personality compared to the usual smooth surface. However, the imperfections can still be noticeable even if you have some paint on it already. But it’s not a bad idea if you want to save some time and effort.

How to paint an ugly wall depends on your plan. If you just want to make it look better, then textured painting can work well already. You can even have more styles to choose from. If you feel like being creative, you can even have used different tools to do your textured painting. Try sponge, brush, brooms, rags, and even your fingers.

3. Be Creative

Ugly walls can inspire you to be creative. You can use how it looks and it’s texture to look better. Try the faux painting technique. Instead of hiding the flaws from the wall surface, you can highlight and enhance it instead. Instead of trying to smoothen the uneven surface, you can use two-toned paint color so it will look as if it’s intentional but will look creative.

The best idea to create a better look with your ugly wall is to play with colors and textures. Then you can use a sponge instead of brushes to paint it. You can just do some rubbing and sponging so that it will look more creative. You don’t have to deal with ugly walls after you are done with this technique and you don’t even have to do too much painting job from there.

Conclusion

How to paint an ugly wall depends on what you want to achieve to be its new look. You don’t have to make it too perfect to make your walls look nice. All you need is to have a little creativity and you should have a better-looking wall in no time.